NVIDIA Pixel Clock Patcher

[sephr]

Just chiming in to say that 344.48 is working fine with the 1.2.6 patcher, in case anyone is coming here to check.

[ToastyX]

(10-09-2014 05:25 PM)GoldenTiger Wrote:  I had been trying to get DSR on my GTX 970 SLI working with custom resolutions afforded by the patched pixel clock using a 2560x1440 X-Star DP2710. Until the new 344.24 WHQL driver DSR would not enable for me with any EDID patched resolution with the Pixel Clock Patcher used. As of 344.24 I can now enable DSR & SLI with a custom resolution using CRU + this thread's patcher, however if I go above the 400mhz default DL-DVI limit DSR seems to be disabled. I'm unsure if this is a driver limitation or if this is something your tool could address somehow, as it may be an additional DL-DVI clock check they added in the drivers somewhere if I were to hazard a guess. This is letting me do 97hz + DSR at 2560x1440 which is great though compared to the prior versions.

I just tested DSR now that they've added support for Fermi in 334.48, but I'm not seeing a 400 MHz limit. I'm not able to test DSR with SLI though, so I don't know if there's a separate limitation there.

[PFS]

344.48 driver not working with patcher, sli limit 2 not found using full patcher.
Please update Toasty x

[ToastyX]

(11-03-2014 07:18 AM)PFS Wrote:  344.48 driver not working with patcher, sli limit 2 not found using full patcher.
Please update Toasty x

"SLI limit 2" doesn't exist in 344.xx. Have you checked if SLI works?

[PFS]

New driver out 344.60, have not tried the patcher yet with previous driver.

[GoldenTiger]

(10-29-2014 02:59 PM)ToastyX Wrote:  

(10-09-2014 05:25 PM)GoldenTiger Wrote:  I had been trying to get DSR on my GTX 970 SLI working with custom resolutions afforded by the patched pixel clock using a 2560x1440 X-Star DP2710. Until the new 344.24 WHQL driver DSR would not enable for me with any EDID patched resolution with the Pixel Clock Patcher used. As of 344.24 I can now enable DSR & SLI with a custom resolution using CRU + this thread's patcher, however if I go above the 400mhz default DL-DVI limit DSR seems to be disabled. I'm unsure if this is a driver limitation or if this is something your tool could address somehow, as it may be an additional DL-DVI clock check they added in the drivers somewhere if I were to hazard a guess. This is letting me do 97hz + DSR at 2560x1440 which is great though compared to the prior versions.

I just tested DSR now that they've added support for Fermi in 334.48, but I'm not seeing a 400 MHz limit. I'm not able to test DSR with SLI though, so I don't know if there's a separate limitation there.

Hi!

Sorry for the late reply but I finally tried again using the new 344.60 WHQL and you're right, it was related to DSR... it was probably PEBKAC on my end with 344.88 but the patcher works fine at least for me on 344.60, though the drivers then disable the DSR option with any pixel clocks set over 400mhz (though the refresh rate takes as it should be).

Thanks and have a good day!

[llmavll]

Just loaded 344.65 and using patch 1.2.6. "SLI Limit 2 : not found"

I have SLI enabled thru the Nvidia panel...is SLI not working on this one?

I am running 2 GTX 680's

Thanks in advance.
Mav

[ToastyX]

(11-17-2014 02:45 AM)llmavll Wrote:  Just loaded 344.65 and using patch 1.2.6. "SLI Limit 2 : not found"

I have SLI enabled thru the Nvidia panel...is SLI not working on this one?

"SLI limit 2" doesn't exist in 344.xx. I need you to tell me if SLI works because I can't test it myself. If you can use resolutions beyond 400 MHz pixel clock without it freezing every few seconds, then it's working fine.

[kajba]

(11-17-2014 02:55 AM)ToastyX Wrote:  

(11-17-2014 02:45 AM)llmavll Wrote:  Just loaded 344.65 and using patch 1.2.6. "SLI Limit 2 : not found"

I have SLI enabled thru the Nvidia panel...is SLI not working on this one?

"SLI limit 2" doesn't exist in 344.xx. I need you to tell me if SLI works because I can't test it myself. If you can use resolutions beyond 400 MHz pixel clock without it freezing every few seconds, then it's working fine.

Hey!

I bought a 750Ti card and i have patched with the patcher, rebooted and then tried to change/add resolution with both the Control Panel and CRU but the added resolution doesnt show up even when i have crossed to enable custom resolution.

Any idea? tried with newest driver available and 340.65.

The hertz I can change to is 61 at tops but in CRU i can add more than 100hz but the resolution isnt shown even though a reboot is done.

EDIT:

Solved it now but not sure what solved it..

Installed Catleap drivers, i got Yamasaki mon
Imported blank.dat file in CRU

[grirvan]

Kajba, I just received my Catleap yesterday and will begin to install tonight. Can you advise on where to get the drivers you mentioned and any other advice would be GREATLY appreciated!